Vacon 100 HVAC Скачать руководство пользователя

Страница: 181 / 201

Selection

number

Selection name

Description

Disabled

In normal operation, the sequence of the motors is always 1,

2, 3, 4, 5. The sequence can change during the operation if

you add or remove interlocks. After the drive stops, the

sequence always changes back.

Enabled

The system changes the sequence at intervals to wear the

motors equally. You can adjust the intervals of the autoch-

ange.

To adjust the intervals of the autochange, use P3.14.5 Autochange Interval. You can set the

maximum number of motors that can operate with parameter Autochange: Motor Limit

(P3.14.7). You can also set the maximum frequency of the regulating motor (Autochange:

Frequency Limit P3.14.6).

When the process is in the limits that are set with parameters P3.14.6 and P3.14.7, the

autochange occurs. If process is not in these limits, the system will wait until the process is

in the limits, and do the autochange after that. This prevents sudden pressure drops during

the autochange when a high capacity at a pump station is necessary.

EXAMPLE

After an autochange, the first motor is put last. The other motors move up 1 position.

The start sequence of the motors: 1, 2, 3, 4, 5

--> Autochange -->

The start sequence of the motors: 2, 3, 4, 5, 1

--> Autochange -->

The start sequence of the motors: 3, 4, 5, 1, 2

P3.14.5 AUTOCHANGE INTERVAL (ID 1029)

Use this parameter to adjust the autochange intervals.

This parameter defines how often to rotate the starting order of the motors/pumps. The

autochange is done when the number of running motors is below the autochange motor limit

and the frequency is below the autochange freq limit.

When the autochange interval has elapsed, the autochange occurs if the capacity is below the

level set with P3.14.6. and P3.14.7.

P3.14.6 AUTOCHANGE: FREQUENCY LIMIT (ID 1031)

Use this parameter to set the autochange frequency limit.

An autochange is done when the autochange interval has elapsed, the number of running

motors is less than autochange motor limit and the controlling drive is running below

autochange frequency limit.

P3.14.7 AUTOCHANGE: MOTOR LIMIT (ID 1030)

Use this parameter to set the amount of pumps used in Multi-pump function.

PARAMETER DESCRIPTIONS

VACON · 181

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды