Vacon 100 HVAC Скачать руководство пользователя

Страница: 116 / 201

This is done to prevent the operation of the PM motor in the field weakening area. The

nominal voltage of the PM motor is much lower than the full output voltage of the drive.

The nominal voltage of the PM motor agrees to the back-EMF voltage of the motor at

nominal frequency. But in a different motor manufacturer, it can be equal to, for example,

the stator voltage at nominal load.

Stator Voltage Adjust helps you to adjust the U/f curve of the drive near the back-EMF curve.

It is not necessary to change the values of many U/f curve parameters.

The parameter P3.1.2.17 gives the output voltage of the drive in percentage of the nominal

voltage of the motor at the nominal frequency of the motor. Adjust the U/f curve of the drive

above the back-EMF curve of the motor. The motor current increases the more the U/f curve

is different from the back-EMF curve.

Field

Weakening

Point

Field Weakening

Point Voltage

Motor Nominal

Voltage

Motor Nominal

Frequency

Stator Voltage Adjust

back

-EMF

Zero Frequency

Voltage

(50..200%)

200%

100%

50%

f [Hz]

U [V]

Fig. 14: The stator voltage adjustment

P3.1.2.18 ENERGY OPTIMIZATION (ID 666)

Use this parameter to enable the Energy Optimization function.

To save energy and to lower the motor noise, the drive searches for the minimum motor

current. You can use this function for example in fan and pump processes. Do not use the

function with fast PID controlled processes.

P3.1.2.19 FLYING START OPTIONS (ID 1590)

Use this parameter to set the flying start options.

The parameter Flying Start Options has a checkbox selection of values.

The bits can receive these values.

•

Disable reverse direction search

•

Flux build with current control

VACON · 116

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды