Vacon 100 HVAC Скачать руководство пользователя

Страница: 176 / 201

When to disconnect and/or remove motors:

•

The feedback value is not in the bandwidth area.

•

The regulating motor operates at a close to minimum frequency (+2 Hz).

•

The conditions above are true for longer than the bandwidth delay.

•

There are more motors that operate than the regulating one.

P3.14.1 NUMBER OF MOTORS (ID 1001)

Use this parameter to set the total number of motors/pumps used with the Multi-Pump

system.

P3.14.2 INTERLOCK FUNCTION (ID 1032)

Use this parameter to enable or disable the interlocks.

The interlocks tell the Multipump system that a motor is not available. This can occur when

the motor is removed from the system for maintenance or bypassed for manual control.

To use the interlocks, enable the parameter P3.14.2. Make a selection of the status for each

motor with a digital input (the parameters from P3.5.1.25 to P3.5.1.28). If the value of the

input is CLOSED, that is, active, the motor is available for the Multipump system. If not, the

Multipump logic will not connect it.

Starting order of motors

Fig. 45: The interlock logic 1

The sequence of the motors is 1, 2, 3, 4, 5.

If you remove the interlock of Motor 3, that is, you set the value of P3.5.1.36 is set to OPEN,

the sequence changes to 1, 2, 4, 5.

VACON · 176

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды