Vacon 100 HVAC Скачать руководство пользователя

Страница: 195 / 201

Table 61: Fault codes

Fault

code

Fault ID Fault name

Possible cause

How to correct the fault

180

Power overload

(short-time supervi-

sion)

The power of the drive is too

high.

Decrease the load.

181

Power overload

(long-time supervi-

sion)

Motor control fault

A malfunction in the start

angle identification.

A generic motor control

fault.

290

Safe Off

The safe Off signal A does

not let you to set the drive to

the READY state.

Reset the fault and restart the

drive.

Do a check of the signals from the

control board to the power unit and

the D connector.

291

Safe Off

The safe Off signal B does

not let you to set the drive to

the READY state.

500

Safety configuration

The safety configuration

switch was installed.

Remove the safety configuration

switch from the control board.

501

Safety configuration

There are too many STO

option boards. It is possible

to have only 1.

Keep 1 of the STO option boards.

Remove the others. See the safety

manual.

502

Safety configuration

The STO option board was

installed in an incorrect slot.

Put the STO option board into the

correct slot. See the safety man-

ual.

503

Safety configuration

There is no safety configura-

tion switch on the control

board.

Install the safety configuration

switch on the control board. See

the safety manual.

504

Safety configuration

The safety configuration

switch was installed incor-

rectly on the control board.

Install the safety configuration

switch into the correct position on

the control board. See the safety

manual.

505

Safety configuration

The safety configuration

switch was installed incor-

rectly on the STO option

board.

Do a check of the installation of the

safety configuration switch on the

STO option board. See the safety

manual.

506

Safety configuration

There is no communication

with the STO option board.

Do a check of the installation of the

STO option board. See the safety

manual.

507

Safety configuration

The STO option board is not

compatible with the hard-

ware.

Reset the drive and restart it. If the

fault occurs again, ask instructions

from your nearest distributor.

FAULT TRACING

VACON · 195

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды