Vacon 100 HVAC Скачать руководство пользователя

Страница: 144 / 201

Table 60: The output signals through RO1

Selection

number

Selection name

Description

Not used

The output is not used.

Ready

The AC drive is ready to operate.

Run

The AC drive operates (the motor runs).

General fault

A fault trip occurred.

General fault inverted

A fault trip did not occur.

General alarm

Reversed

The reverse command is given.

At speed

The output frequency has become the same as the set fre-

quency reference.

Motor regulator activated

One of the limit regulators (for example current limit or tor-

que limit) is activated.

Preset Frequency active

The selection of preset frequency was made with digital input

signals.

Keypad control active

The selection is keypad control (the active control place is

keypad).

I/O control B active

The selection is I/O control place B (the active control place

is I/O B).

Limit supervision 1

The limit supervision activates if the signal value goes below

or above the set supervision limit (P3.8.3 or P3.8.7).

Limit supervision 2

Start command active

Start command is active.

Reserved

Fire mode ON

RTC timer 1 control

Time channel 1 is in use.

RTC timer 2 control

Time channel 2 is in use.

RTC timer 3 control

Time channel 3 is in use.

FB Control WordB 13

FB Control WordB 14

FB Control WordB 15

PID in Sleep mode

VACON · 144

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды