Vacon 100 HVAC Скачать руководство пользователя

Страница: 192 / 201

11.3

FAULT CODES

Table 61: Fault codes

Fault

code

Fault ID Fault name

Possible cause

How to correct the fault

Overcurrent (hard-

ware fault)

There is too high a current

(>4*I H) in the motor cable.

Its cause can be 1 of these.

•

a sudden heavy load

increase

•

a short circuit in the

motor cables

•

the motor is not the

correct type

Do a check of the loading.

Do a check of the motor.

Do a check of the cables and con-

nections.

Do a check of the ramp times.

Overcurrent (software

fault)

Overvoltage (hard-

ware fault)

The DC-link voltage is

higher than the limits.

•

too short a decelera-

tion time

•

high overvoltage spikes

in the supply

•

Start/Stop sequence

too fast

Set the deceleration time longer.

Activate the overvoltage controller.

Do a check of the input voltage.

Overvoltage (software

fault)

Earth fault (hardware

fault)

The measurement of cur-

rent tells that the sum of the

motor phase current is not

zero.

•

an insulation malfunc-

tion in the cables or the

motor

Do a check of the motor cables and

the motor.

Earth fault (software

fault)

Charging switch

The charging switch is open,

when the START command

is given.

•

operation malfunction

•

defective component

Reset the fault and restart the

drive.

If the fault occurs again, ask

instructions from the distributor

near to you.

Saturation

•

Defective component

This fault cannot be reset from the

control panel.

Switch off the power. DO NOT

RESTART THE DRIVE or CONNECT

THE POWER!

Ask instructions from the factory.

If this fault shows together with F1,

do a check of the motor cables and

motor.

VACON · 192

FAULT TRACING

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды