Vacon 100 HVAC Скачать руководство пользователя

Страница: 158 / 201

ID714

ID715

5 Hz

Underload area

Torque

Field weakening

point

Fig. 31: Setting of the minimum load

P3.9.17 UNDERLOAD PROTECTION: ZERO FREQUENCY LOAD (ID 715)

Use this parameter to set the minimum torque that the motor needs when the output

frequency of the drive is 0.

P3.9.18 UNDERLOAD PROTECTION: TIME LIMIT (ID 716)

Use this parameter to set the maximum time for an underload state.

You can set the time limit between 2.0 and 600.0 s.

This is the maximum time for an underload status to be active. An internal counter counts

the underload time. If the value of the counter goes above this limit, the protection causes

the drive to trip. The drive trips as is set in parameter P3.9.15 Underload Fault. If the drive

stops, the underload counter goes back to 0.

ID716

Trip area

Time

Underload time counter

Underload•

No underl.

Trip/warning

ID713

Fig. 32: The Underload time counter function

VACON · 158

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды