Vacon 100 HVAC Скачать руководство пользователя

Страница: 135 / 201

In the Edit mode, the slot value DigIN SlotA is

underlined and blinks. If you have more digital

inputs available in your I/O, for example, because of

option boards in slots C, D or E, make a selection of

them.

STOP

READY

I/O

Ext Fault Close

P3.5.1.7

ID:405

Min:
Max:

DigIN SlotA.3

To activate the terminal 3, push the arrow button

Right again.

STOP

READY

I/O

Ext Fault Close

P3.5.1.7

ID:405

Min:
Max:

DigIN SlotA.3

To change the terminal to 6, push the arrow button

Up 3 times. Accept the change with the OK button.

STOP

READY

I/O

Ext Fault Close

P3.5.1.7

ID:405

Min:
Max:

DigIN SlotA.6

If the digital input DI6 was already used for some

other function, a message shows on the display.

Change one of these selections.

STOP

READY

I/O

ID:

At least one digital input has
been selected to several
operations.
To prevent possible unwanted
operations, please check all
digital input selection parameters.

PARAMETER DESCRIPTIONS

VACON · 135

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды