Vacon 100 HVAC Скачать руководство пользователя

Страница: 128 / 201

This parameter defines when the reference of the motor potentiometer is set to 0.

There are 3 selections in the reset function: no reset, reset when the drive stops, or reset

when the drive is powered down.

Selection

number

Selection name

Description

No reset

The last motor potentiometer frequency reference is kept

through the stop state and kept in memory if a powerdown

occurs.

Stop state

The motor potentiometer frequency reference is set to 0

when the drive goes to the stop state, or when the drive is

powered down.

Powered down

The motor potentiometer frequency reference is set to 0 only

when a powerdown occurs.

P3.3.22 REVERSE DIRECTION (ID 15530)

Use this parameter to permit running in reverse direction.

10.4

RAMPS AND BRAKES SETUP

P3.4.1 RAMP 1 SHAPE (ID 500)

Use this parameter to make the start and the end of the acceleration and deceleration ramps

smoother.

With the parameter Ramp 1 Shape, you can make smoother the start and the end of the

acceleration and deceleration ramps. If you set the value to 0, you get a linear ramp shape.

The acceleration and deceleration act immediately to the changes in the reference signal.

When you set the value between 0.1 and 10 s, you get an S-shaped acceleration or

deceleration ramp. Use this function to reduce mechanical erosion of the parts and current

spikes when the reference changes. You can modify the acceleration time with parameters

P3.4.2 (Acceleration Time 1) and P3.4.3 (Deceleration Time 1).

VACON · 128

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды