Vacon 100 HVAC Скачать руководство пользователя

Страница: 117 / 201

The bit B0 controls the search direction. When you set the bit to 0, the shaft frequency is

searched in 2 directions, the positive and the negative. When you set the bit to 1, the shaft

frequency is searched only in the frequency reference direction. This prevents the shaft

movements for the other direction.

The bit 6 gives an enhanced procedure to magnetise an induction motor. It can help, for

example, with high power motors.

P3.1.2.20 I/F START (ID 534)

Use this parameter to enable the I/f Start function.

This function starts the motor with constant current control. It provides a sufficient torque

for the motor at startup. You can use this function for example with PM-motors.

P3.1.2.21 I/F START FREQUENCY (ID 535)

Use this parameter to set the output frequency limit below which the set I/f start current is

fed to motor.

When the output frequency of the drive is below the limit of this parameter, I/f Start function

activates. When the output frequency is more than the limit, the drive operation mode

changes back to the normal U/f control mode.

P3.1.2.22 I/F START CURRENT (ID 536)

Use this parameter to set the current that is used when the I/f Start function is enabled.

10.2

START/STOP SETUP

P3.2.1 REMOTE CONTROL PLACE (ID 172)

Use this parameter to select the remote control place (start/stop).

Use this parameter to change back to remote control from Vacon Live, for example if the

control panel is broken.

P3.2.2 LOCAL/REMOTE (ID 211)

Use this parameter to switch between the local and remote control places.

Local control place is always keypad control. The remote control place can be I/O or

Fieldbus, depending on the 'Remote Control Place' parameter value.

P3.2.3 KEYPAD STOP BUTTON (ID 114)

Use this parameter to enable the keypad stop button.

When this function is enabled, a press of keypad stop button always stops the drive

(regardless of the control place). When this function is disabled, a press of keypad stop

button stops the drive in local control only.

PARAMETER DESCRIPTIONS

VACON · 117

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды