Vacon 100 HVAC Скачать руководство пользователя

Страница: 124 / 201

7. The Run enable signal is set to OPEN,

which causes the frequency to go to 0.

Configure the Run enable signal with

parameter P3.5.1.10.

8. Before the drive can start, you must

open and close CS1 again.

9. The STOP button on the keypad is

pushed and the frequency that is fed to

the motor goes to 0. (This signal only

works if the value of P3.2.3 Keypad Stop

Button is Yes.)

10. Before the drive can start, you must

open and close CS1 again.

11. CS1 becomes inactive and the frequency

goes to 0.

P3.2.7 I/O B START/STOP LOGIC (ID 363)

Use this parameter to control the start and stop of the drive with the digital signals.

The selections can include the word 'edge' to help you prevent an accidental start.

See P3.2.6 for more information.

P3.2.8 FIELDBUS START LOGIC (ID 889)

Use this parameter to set the fieldbus start logic.

The selections can include the word 'edge' to help you prevent an accidental start.

Selection

number

Selection name

Description

A rising edge is necessary

State

10.3

REFERENCES

10.3.1

FREQUENCY REFERENCE

P3.3.1 MINIMUM FREQUENCY REFERENCE (ID 101)

Use this parameter to set the minimum frequency reference.

P3.3.2 MAXIMUM FREQUENCY (ID 102)

Use this parameter to set the maximum frequency reference.

P3.3.3 I/O CONTROL REFERENCE A SELECTION (ID 117)

Use this parameter to select the reference source when the control place is I/O A.

P3.3.4 I/O CONTROL REFERENCE B SELECTION (ID 131)

Use this parameter to select the reference source when the control place is I/O B.

You can force the I/O B control place to be active only with a digital input (P3.5.1.5).

VACON · 124

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды