Vacon 100 HVAC Скачать руководство пользователя

Страница: 120 / 201

12. The STOP button on the keypad is

pushed again to stop the drive.

13. The attempt to start the drive with the

START button is not successful, because

CS1 is inactive.

Selection

number

Selection name

Description

CS1 = Forward (edge)

CS2 = Inverted stop

Set frequency

0 Hz

Keypad stop

button

Output

frequency

FWD

REV

Ctrl signal 2

Ctrl signal 1

Run enable

Set frequency

Fig. 16: I/O A Start/stop logic = 1
1. Control signal (CS) 1 activates and

causes the output frequency to increase.

The motor operates forward.

2. CS2 becomes inactive and causes the

frequency to go to 0.

3. CS1 activates and causes the output

frequency to increase again. The motor

operates forward.

4. The Run enable signal is set to OPEN,

which causes the frequency to go to 0.

Configure the Run enable signal with

parameter 3.5.1.10.

5. The start attempt with CS1 is not

successful, because the Run enable

signal is still OPEN.

6. CS1 activates and the motor accelerates

(FWD) to the set frequency, because the

Run enable signal was set to CLOSED.

7. The STOP button on the keypad is

pushed, and the frequency that is fed to

the motor goes to 0. (This signal only

works if the value of P3.2.3 Keypad Stop

Button is Yes.)

8. CS1 activates and causes the output

frequency to increase again. The motor

operates forward.

VACON · 120

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды