Vacon 100 HVAC Скачать руководство пользователя

Страница: 173 / 201

10.12.6 PRESSURE LOSS COMPENSATION

When you pressurise a long pipe that has many outlets, the best position for the sensor is in

the middle of the pipe (the position 2 in the figure). You can also put the sensor directly after

the pump. This gives the right pressure directly after the pump, but farther in the pipe, the

pressure drops with the flow.

Fig. 42: The position of the pressure sensor
A. Pressure

B. No flow

C. With flow

D. Pipe length

E. Position 1

F. Position 2

P3.12.6.1 ENABLE SETPOINT 1 (ID1189)

Use this parameter to enable the pressure loss compensation in the pump system.

P3.12.6.2 SETPOINT 1 MAX COMPENSATION (ID 1190)

Use this parameter to set the maximum compensation for PID setpoint value that is applied

when the output frequency of the drive is at the maximum frequency.

The sensor is put in position 1. The pressure in the pipe stays constant when there is no flow.

But with flow, the pressure decreases farther in the pipe. To compensate for this, lift the

setpoint as the flow increases. Then the output frequency makes an estimate of the flow, and

the setpoint increases linearly with the flow.

PARAMETER DESCRIPTIONS

VACON · 173

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды