Vacon 100 HVAC Скачать руководство пользователя

Страница: 154 / 201

The default value is set for conditions where there is no external fan. If you use an external

fan, you can set the value higher than without the fan, for example at 90%.

If you change parameter P3.1.1.4 (Motor Nominal Current), parameter P3.9.2.3 is

automatically set to its default value.

Although you change this parameter, it does not have an effect on the maximum output

current of the drive. Only parameter P3.1.1.7 Motor Current Limit can change the maximum

output current.

The corner frequency for the thermal protection is 70% of the value of the parameter

P3.1.1.2 Motor Nominal Frequency.

ID706=40%

100%

Overload area

Pcooling

Corner freq

Fig. 28: The motor thermal current I

curve

P3.9.9 MOTOR THERMAL TIME CONSTANT (ID 707)

Use this parameter to set the motor thermal time constant.

The time constant is the time during which the calculated warming curve becomes 63% of its

target value. The length of the time constant is in relation with the dimension of the motor.

The bigger the motor, the longer the time constant.

In different motors, the motor thermal time constant is different. It also changes between

different motor manufacturers. The default value of the parameter changes from dimension

to dimension.

The t6-time is the time in seconds that the motor can safely operate at 6 times the rated

current. It is possible that the motor manufacturer gives the data with the motor. If you know

the t6 of the motor, you can set the time constant parameter with its help. Usually, the motor

thermal time constant in minutes is 2*t6. When the drive is in the STOP state, the time

constant is internally increased to 3 times the set parameter value, because the cooling

operates based on convection. See Fig. 29 The calculation of the motor temperature.

VACON · 154

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды