Vacon 100 HVAC Скачать руководство пользователя

Страница: 38 / 201

D. The current location in the menu

E. The indicators of the control place

F. The indicators of the rotation direction

3.3.1

EDITING THE VALUES

CHANGING THE TEXT VALUE OF A PARAMETER

Set the value of a parameter with this procedure.

Find the parameter with the arrow buttons.

READY

FAULT

ALARM

STOP

RUN

BUS

KEYPAD

I/O

REV

FWD

To go to the Edit mode, push the OK button.

READY

FAULT

ALARM

STOP

RUN

BUS

KEYPAD

I/O

REV

FWD

To set a new value, push the arrow buttons Up and

Down.

READY

FAULT

ALARM

STOP

RUN

KEYPAD

I/O

REV

FWD

BUS

Accept the change with the OK button. To ignore

the change, go back to the level where you were

before with the Back/Reset button.

EDITING THE NUMERICAL VALUES

Find the parameter with the arrow buttons.

Go to the Edit mode.

VACON · 38

USER INTERFACES

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды