Vacon 100 HVAC Скачать руководство пользователя

Страница: 151 / 201

P3.7.7 RAMP TIME FACTOR (ID 518)

Use this parameter to set the multiplier of the selected ramp times when the output

frequency of the drive is between the prohibited frequency limits.

The Ramp Time Factor sets the acceleration and the deceleration time when the output

frequency is in a prohibited frequency range. The value of the Ramp Time Factor is multiplied

with the value of P3.4.2 (Acceleration Time 1) or P3.4.3 (Deceleration Time 1). For example,

the value 0.1 makes the acceleration/deceleration time ten times shorter.

F [s]

[Hz]

Fig. 27: The parameter Ramp Time Factor
A. Output Frequency

B. High Lim

C. Low Lim

D. Ramp Time Factor = 0.3

E. Ramp Time Factor = 2.5

F. Time

10.8

LIMIT SUPERVISIONS

P3.8.1 SUPERVISION #1 ITEM SELECTION (ID 1431)

Use this parameter to select the supervision item.

The output of the supervision function can be selected to the relay output.

P3.8.2 SUPERVISION #1 MODE (ID 1432)

Use this parameter to set the supervision mode.

When the 'Low limit' mode is selected, the output of the supervision function is active when

the signal is below the supervision limit.

When the'High limit' mode is selected, the output of the supervision function is active when

the signal is above the supervision limit.

P3.8.3 SUPERVISION #1 LIMIT (ID 1433)

Use this parameter to set the supervision limit for the selected item.

The unit shows automatically.

PARAMETER DESCRIPTIONS

VACON · 151

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды