manualshive.com logo in svg

Texas Instruments TMS570LC4357, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

Module Operation

1269

SPNU563A – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

FlexRay Module

26.2.13.2.1 Host Handling of Uncorrectable ECC Multi-bit Errors

Uncorrectable errors caused by transient bit flips can be fixed by:

Self-healing

Uncorrectable errors located in:

•

Input Buffer RAM 1,2

•

Output Buffer RAM 1,2

•

Data Section of Message RAM

•

Transient Buffer RAM A

•

Transient Buffer RAM B

•

Transfer Configuration RAM (TCR)

are overwritten with the next write access to the disturbed bit(s) caused by host access or by FlexRay
communication.

CLEAR_RAMS Command

When called in DEFAULT_CONFIG or CONFIG state POC command CLEAR_RAMS initializes all
module-internal RAMs to 0 and the ECC bits are initialized accordingly, depending what mode is enabled.

Temporary Unlocking of Header Section

An uncorrectable error in the header section of a locked message buffer can be fixed by a transfer from
the input buffer to the locked buffer header section. For this transfer, the write-access to the IBCR
(specifying the message buffer number) must be immediately preceded by the unlock sequence normally
used to leave CONFIG state. For that single transfer the corresponding message buffer header is
unlocked, regardless whether it belongs to the FIFO or whether its locking is controlled by MRC.SEC(1-0),
and will be updated with new data.

NOTE:

In case the previous methods do not work, it is recommended to execute the PBIST test at

device level to confirm a hard error in the module internal RAMs.

26.2.14 Interrupts

This section describes the transfer unit interrupts and the communication controller interrupts.

26.2.14.1 Transfer Unit Interrupts

26.2.14.1.1 Interrupt Structure

For transfer interrupts, one enable bit is provided for each bit in the transfer occurred status registers.
Maskable error interrupts are possible for all error conditions except ECC multi-bit error and memory
protection error.

The ECC multi-bit error and the memory protection error have separate non-maskable lines. Both turn off
the Transfer Unit after finishing the current word access cycle.

The single-bit error interrupt is maskable. On single-bit error, if single-bit error correction is turned off, the
Transfer Unit is turned off after finishing the current word access cycle.

Figure 26-30

shows the interrupt structure of the FlexRay Transfer Unit.

Содержание TMS570LC4357

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS570LC4357

Parker 890CS Product Manual preview
890CS
Бренд: Parker Страницы: 478
Abov MC80F0304 User Manual preview
MC80F0304
Бренд: Abov Страницы: 138
POLA HP49 Handbook preview
HP49
Бренд: POLA Страницы: 2
KaMo Pearldex Series Manual preview
Pearldex Series
Бренд: KaMo Страницы: 2
Joy-it Moto1 Quick Start Manual preview
Moto1
Бренд: Joy-it Страницы: 7
Nice One-Max Installation And Use Instructions And Warnings preview
One-Max
Бренд: Nice Страницы: 32
Harmonic Drive RSF-B mini Series Manual preview
RSF-B mini Series
Бренд: Harmonic Drive Страницы: 32
Freescale Semiconductor RS08 Designer Reference Manual preview
RS08
Бренд: Freescale Semiconductor Страницы: 34
Matelec FPC-12720 Quick Start Manual preview
FPC-12720
Бренд: Matelec Страницы: 2
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Бренд: DAYLIFF Страницы: 40
Swagelok KPF Series Maintenance Instructions Manual preview
KPF Series
Бренд: Swagelok Страницы: 6
ez-wheel SWD Starter Kit Instruction Manual preview
SWD Starter Kit
Бренд: ez-wheel Страницы: 30
adept technology sDIO User Manual preview
sDIO
Бренд: adept technology Страницы: 96
Watlow Integrated Controller Rev C EZ-ZONE PM User Manual preview
Integrated Controller Rev C EZ-ZONE PM
Бренд: Watlow Страницы: 80
J+J J4C B140 Handbook preview
J4C B140
Бренд: J+J Страницы: 91
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Бренд: Galcon Страницы: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Бренд: NXP Semiconductors Страницы: 5
National Instruments GPIB PCI-GPIB Getting Started preview
GPIB PCI-GPIB
Бренд: National Instruments Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды