manualshive.com logo in svg

Suzuki RM-Z250, Руководство по обслуживанию


Поделиться
Скачать
background image

13-4     FUEL SYSTEM AND THROTTLE BODY

• When installing the fuel pump assembly 

2

, first tighten all the

fuel pump mounting bolts 

3

 lightly and then to the specified

torque.

Fuel pump mounting bolt: 10 N·m (1.0 kgf-m, 7.0 lbf-ft)

• Connect the fuel hose 

4

 to the fuel pump until it locks

securely (a click is heard).

FUEL PRESSURE INSPECTION

• Remove the seat and radiator covers. (

5-2)

• Remove the fuel tank bolt and rubber band. (

13-2)

• Lift and hold the fuel tank.
• Place a rag under the fuel hose and remove the fuel hose 

1

.

• Disconnect the fuel pump coupler 

2

.

• Install the special tools between the fuel pump and fuel deliv-

ery pipe.

09915-74521: Adapter hose
09915-77331: Oil pressure gauge (1 000 kPa)
09940-40211: Fuel pressure gauge adaptor
09940-40220: Fuel pressure gauge attachment

A

 To fuel pump

B

 To fuel delivery pipe

Be sure to connect the fuel hose 

4

 by your hand. You

may not connect the fuel hose 

4

 with any tool.

Be sure to disconnect the fuel hose 

1

 by your hand.

You may not disconnect the fuel hose 

1

 with any tool.

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

HRC '92-RS125R Owner'S Manual preview
'92-RS125R
Бренд: HRC Страницы: 88
GAS GAS TXT PRO - PART LIST 2010 Parts List preview
TXT PRO - PART LIST 2010
Бренд: GAS GAS Страницы: 64
CYCLOPS KTM 1190 LED Light Bar Instructions preview
KTM 1190 LED Light Bar
Бренд: CYCLOPS Страницы: 4
BSA B40 VICTOR W D 1967 Workshop Manual preview
B40 VICTOR W D 1967
Бренд: BSA Страницы: 128
Honda CBF600N 2006 Owner'S Manual preview
CBF600N 2006
Бренд: Honda Страницы: 150
AMFD RideMaxx Quick Start Manual preview
RideMaxx
Бренд: AMFD Страницы: 17
Can-Am 219 002 095 Operator'S Manual preview
219 002 095
Бренд: Can-Am Страницы: 196
Caberg Droid Manual preview
Droid
Бренд: Caberg Страницы: 16
Evotech Performance KAWASAKI ZX6R 2007/8 Installation Instructions preview
KAWASAKI ZX6R 2007/8
Бренд: Evotech Performance Страницы: 2
Gilera Fuoco 500 Service Station Manual preview
Fuoco 500
Бренд: Gilera Страницы: 396
Barnett Scorpion 608-30-10086 Installation Manual preview
Scorpion 608-30-10086
Бренд: Barnett Страницы: 2
Dynafit ST User Instructions preview
ST
Бренд: Dynafit Страницы: 48
Dräger HPS 3500 Instructions For Use Manual preview
HPS 3500
Бренд: Dräger Страницы: 164
Cagiva Roadster 521 Workshop Manual preview
Roadster 521
Бренд: Cagiva Страницы: 230
Petzl METEOR Technical Notice preview
METEOR
Бренд: Petzl Страницы: 15
Gilera Nexus 250 i.e. Manual preview
Nexus 250 i.e.
Бренд: Gilera Страницы: 96
KTM 350 SC-F Owner'S Manual preview
350 SC-F
Бренд: KTM Страницы: 105
X-lite X-1004 Safety And Instructions For Use preview
X-1004
Бренд: X-lite Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды