Suzuki RM-Z250 Скачать руководство пользователя страница 393

Страница: 393 / 411

SERVICING INFORMATION 20-21

CABLE ROUTING

Throttle cable (Pulling cable)

Bind the hot starter cable and wiring harness with the
clamp.

Throttle cable (Returning cable)

*3 Pass the hot starter cable inside of frame bridge.

Hot starter cable

*4 Pass the clutch cable between radiator bracket and frame.

Clutch cable

Pass the overflow hose and wiring harness between radia-
tor hose and frame.

Radiator overflow hose

Pass the overflow hose between engine mounting lower
bracket.

Cable guide

Align the matching marks on the clutch cable bracket and
on the clutch cable.

2 – 3 mm (0.08 – 0.12 in)

Pass the throttle cable, hot starter cable and engine stop
switch lead wire inside of the cable guide.

14 – 16 mm (0.55 – 0.63 in)

The cable guide must be positioned in parallel with the
frame head with its open end facing upward.

Bind the clutch cable (White protector
position) with the clamp.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды