manualshive.com logo in svg

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 214 / 411

Поделиться
Скачать
Suzuki RM-Z250 Скачать руководство пользователя страница 214

FI SYSTEM DIAGNOSIS     12-31

“14” (P0120-H/L) TP SENSOR CIRCUIT MALFUNCTION

NOTE:
After repairing the trouble, clear the DTC using SDS tool. (

12-21)

INSPECTION
Step 1 (When indicating 14:)

1) Stop the engine.
2) Check the TP sensor coupler 

1

 for loose or poor contacts. 

If OK, then measure the TP sensor input voltage.

3) Disconnect the TP sensor coupler 

1

.

4) Connect a 12 volts battery by using the battery lead wire to

the service coupler. (

12-19)

DETECTED CONDITION

POSSIBLE CAUSE

14

Output voltage is not within the following 
range.
Difference between actual throttle open-
ing and opening calculated by ECM is 
larger than specified value.

0.39 V 

 Sensor voltage < 4.51 V

• TP sensor maladjusted.
• TP sensor circuit open or short.
• TP sensor malfunction.
• ECM malfunction.

P0120

H

Sensor voltage is higher than specified 
value.

• TP sensor circuit shorted to VCC or ground circuit 

open.

• TP sensor circuit open or shorted to ground or 

VCC circuit open.

L

Sensor voltage is lower than specified 
value.

ECM

R/Bl

B/Br

VCC

TP

E2

TP sensor

Y

Bl

Y

B

When using the multi circuit tester, do not strongly touch the terminal of the ECM coupler with
a needle-pointed tester probe to prevent the terminal damage or terminal bend.

1

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов