Suzuki RM-Z250 Скачать руководство пользователя страница 169

Страница: 169 / 411

10-12 TRANSMISSION AND CRANKSHAFT

• Remove the bearing

with the special tools.



09923-74511: Bearing puller
09930-30104: Rotor remover sliding shaft

• Remove the bearing

with the special tools.



09921-20200: Bearing remover (10 mm)
09930-30104: Rotor remover sliding shaft

• Remove the bearing

INSTALLATION

• Press the new bearings with the special tool.



09913-70210: Bearing installer set
Bearing



52 Attachment

Bearing



40 Attachment

Bearing



62 Attachment

Bearing



32 Attachment

Bearing



47 Attachment

Bearing



42 Attachment

Bearing



15 Attachment

• Press the bearing

with the appropriate steel rod.

NOTE:
* Press the bearings (

) into the crankcase, so that

the stamped mark side faces inside of the crankcase.

* Press the bearings (

) into the crankcase, so that the

stamped mark side faces outside of the crankcase.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 169 / 411

Результаты поиска

Содержание RM-Z250

Отзывы: