Suzuki RM-Z250 Скачать руководство пользователя страница 175

Страница: 175 / 411

10-18 TRANSMISSION AND CRANKSHAFT

PRIMARY DRIVE GEAR INSTALLATION

• Install the oil pump No.1, No.2 and oil pump idle gear.

(



11-6 to -8)

• Install the gearshift linkage and GP switch. (



9-5 to -9)

• Install the kick starter idle gear and kick starter shaft assem-

bly. (



8-6, 7)

• Apply grease to the oil seal lip.



99000-25010: SUZUKI SUPER GREASE “A”

or equivalent

• Install the primary drive gear

and washer

NOTE:
The washer is directional. Assemble the washer

as shown in

the illustration.

• Install the clutch component parts. (



7-9, -10)

• Apply THREAD LOCK SUPER to the primary drive gear nut



99000-32110: THREAD LOCK SUPER “1322”

or equivalent

• Hold the magneto rotor with the special tool and tighten the

primary drive gear nut

to the specified torque.





09914-61010: Gear holder



Primary drive gear nut: 90 N·m (9.0 kgf-m, 65.0 lbf-ft)

• Install the cam chain, cam chain tensioner and cam chain

guide retainer. (



6-25)

• Install the key and magneto rotor. (



15-18)

• Install the magneto cover. (



15-19)

• Install the engine top side (piston, cylinder and cylinder head).

(



6-26 to -34)

• Connect the crankcase breather hose

. (



20-23)

• Mount the engine assembly. (



5-6 to -10)

The primary drive gear nut has left-hand threads.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды