Suzuki RM-Z250 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 411

background image

2-36 PERIODIC MAINTENANCE

FRONT FORK

• Move the front fork up and down several times and inspect for

smooth movement.

• Inspect for damage and oil leaks.
• Inspect the bolts and nuts for tightness.
• If any defects are found, replace the front fork with a new one.

• Place a stand under the chassis tube to lift the front wheel off

the ground.

• Remove the air bleeder valve

1

and equalize the air pressure

in the front forks to atmospheric pressure.

• Install the air bleeder valve

1

.



Front fork air bleeder valve: 1.3 N·m (0.13 kgf-m, 1.0 lbf-ft)

REAR SUSPENSION

• Move the rear suspension up and down several times and

inspect for smooth movement.

• Inspect for damage and oil leaks.
• Inspect the bolts and nuts for tightness.
• Inspect that the rear suspension has play or binds by moving

the swingarm up and down, and right and left.

• If necessary, replace the defective parts with a new one.

WHEELS AND TIRES

WHEEL RIM AND TIRES INSPECTION

• Inspect the wheel and tires for damage.
• Inspect the wheel bearing for rattles. (



16-4)

• Inspect the wheel rim runout. (



16-4)

• If necessary, replace the defective parts with a new one.

«
...
50
51
52
53
54
...
»

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

Бренд: R&G Страницы: 10

Бренд: KTM Страницы: 29

Бренд: N-Com Страницы: 6

Бренд: Honda Страницы: 150

Бренд: Dakota Digital Страницы: 11

Бренд: DYNATEK Страницы: 4

1003007FONTANASPRINT

Бренд: DYNATEK Страницы: 7

Бренд: DYNATEK Страницы: 12

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: MSA Страницы: 168

Бренд: Dräger Страницы: 164

Бренд: KTM Страницы: 7

Бренд: ORTILEB Страницы: 16

SUZUKI V-STROM 650 04-UP

Бренд: Mastech Страницы: 2

Бренд: MadStad Engineering Страницы: 8

Бренд: Honda Страницы: 88

Бренд: Honda Страницы: 183

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды