manualshive.com logo in svg

Suzuki RM-Z250, Руководство по обслуживанию


Поделиться
Скачать
background image

13-12     FUEL SYSTEM AND THROTTLE BODY

CLEANING

• Clean all passageways with a spray-type carburetor cleaner

and blow dry with compressed air.

INSPECTION

Check following items for any damage or clogging.

* O-ring
* Throttle valve
* Fuel pipe
* Cushion seal
* Fuel injector

REASSEMBLY

Reassemble the throttle body in the reverse order of disassem-
bly. Pay attention to the following points:

• Install the condenser bracket 

1

.

• Tighten the condenser bracket bolts 

2

 to the specified

torque.

Condenser bracket bolt: 10 N·m (1.0 kgf-m, 7.0 lbf-ft)

Some carburetor cleaning chemicals, especially
dip-type soaking solutions, are very corrosive and
must be handled carefully. Always follow the chemical
manufacturer’s instructions on proper use, handling
and storage.

Do not use wire to clean passageways. Wire can dam-
age passageways. If the components cannot be
cleaned with a spray cleaner it may be necessary to
use a dip-type cleaning solution and allow them to
soak. Always follow the chemical manufacturer’s
instructions for proper use and cleaning of the throttle
body components. Do not apply carburetor cleaning
chemicals to the rubber and plastic materials.

Replace the condenser bracket bolts 

2

 with new

ones.

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

LAMAX eJumper DB50 User Manual preview
eJumper DB50
Бренд: LAMAX Страницы: 134
R&G ECC0364R Fitting Instructions Manual preview
ECC0364R
Бренд: R&G Страницы: 6
Dowco Fastrax 50144-00 Installation Instructions preview
Fastrax 50144-00
Бренд: Dowco Страницы: 3
RDMOTO CF123 Mounting Instructions preview
CF123
Бренд: RDMOTO Страницы: 2
yasuni TUB225 Assembly Instructions Manual preview
TUB225
Бренд: yasuni Страницы: 12
DELTA PLUS Venitex BARRIER Technical Specs preview
Venitex BARRIER
Бренд: DELTA PLUS Страницы: 2
Honda NSC110 2020 Manual preview
NSC110 2020
Бренд: Honda Страницы: 137
GAS GAS EC450 2009 User Manual preview
EC450 2009
Бренд: GAS GAS Страницы: 69
hepco & becker 5054558 00 01 Manual preview
5054558 00 01
Бренд: hepco & becker Страницы: 4
Arai Helmet GP-5X Instruction Manual preview
GP-5X
Бренд: Arai Helmet Страницы: 12
Yamaha YZF-R6T Supplementary Service Manual preview
YZF-R6T
Бренд: Yamaha Страницы: 64
Yamaha YZFR3F Owner'S Manual preview
YZFR3F
Бренд: Yamaha Страницы: 106
Yamaha YZFR3AM 2021 Owner'S Manual preview
YZFR3AM 2021
Бренд: Yamaha Страницы: 108
Yamaha YZF600RS Owner'S Manual preview
YZF600RS
Бренд: Yamaha Страницы: 104
Yamaha YZFR1W 2007 Owner'S Manual preview
YZFR1W 2007
Бренд: Yamaha Страницы: 108
Yamaha YZF155 Owner'S Manual preview
YZF155
Бренд: Yamaha Страницы: 98
Yamaha YZFR1X(C) Owner'S Manual preview
YZFR1X(C)
Бренд: Yamaha Страницы: 118
Yamaha YZF600RC Owner'S Manual preview
YZF600RC
Бренд: Yamaha Страницы: 105

Бренды по названию

Популярные бренды

Загрузить еще бренды