Suzuki RM-Z250 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 411

background image

2-26 PERIODIC MAINTENANCE

VALVE CLEARANCE ADJUSTMENT

The clearance is adjusted by replacing the existing tappet shim
with a thicker or thinner one.

• Remove the intake or exhaust camshafts. (



6-4 to -6)

• Remove the tappet

1

and shim

2

by fingers or magnetic

hand.

• Check the figures printed on the shim. These figures indicate

the thickness of the shim, as illustrated.

• Select a replacement shim that will provide a clearance within

the specified range. For the purpose of this adjustment, tap-
pet shim are available ranging from 1.200 to 2.200 mm in
steps of 0.025 mm. Fit the selected shim to the valve stem
end, with numbers toward tappet. Be sure to check shim size
with micrometer to ensure its size. Refer to the tappet shim
selection table (



2-27, -28) for details.

NOTE:
* Be sure to apply engine oil to tappet shim top and bottom

faces.

* When seating the tappet shim, be sure the figure printed sur-

face faces the tappet.

• Reinstall the camshafts in the specified manner.

(



6-30, -31)

• After replacing the tappet shim and camshafts, rotate the

engine so that the tappet is depressed fully. This will squeeze
out oil trapped between the shim and the tappet that could
cause an incorrect measurement. Then check the clearance
again to confirm that it is within the specified range.

After finishing the valve clearance adjustment, reinstall the fol-
lowing items.

• Cylinder head cover (



6-34)

• Spark plug and ignition coil/plug cap (



2-8)

• Radiator covers and fuel tank
• TDC plug and crankshaft hole plug (



6-33)

• Pour engine oil (



2-13)

• Seat

1.75 mm

175

«
...
40
41
42
43
44
...
»

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

Бренд: Öhlins Страницы: 8

Бренд: KYMCO Страницы: 424

Бренд: R&G Страницы: 2

Windscreen N20012A

Бренд: VStreamT Страницы: 3

Бренд: Yamaha Страницы: 215

Бренд: Yamaha Страницы: 319

Бренд: Yamaha Страницы: 688

XMAX YP250R 2013

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 100

Road Star XV17AWX

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 650

Бренд: hepco & becker Страницы: 2

Бренд: Yamaha Страницы: 93

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды