Suzuki RM-Z250 Скачать руководство пользователя страница 283

Страница: 283 / 411

ELECTRICAL SYSTEM 15-11

IGNITION SYSTEM

NOTE:
The fuel cut-off circuit is incorporated in this ECM in order to prevent over-running of engine.

TROUBLESHOOTING

No spark or poor spark

Step 1

1) Check the ignition system couplers for poor connections.

Is there connection in the ignition system couplers?

Step 2

1) Measure the ignition coil primary peak voltage. (



15-13)

Is the peak voltage OK?

Step 3

1) Inspect the spark plug. (



2-7, -8)

Is the spark plug OK?

YES

Go to Step 2.

Poor connection of couplers

YES

Go to Step 3.

Go to Step 4.

YES

• Poor connection of the spark plug
• Go to Step 4.

Faulty spark plug

Magneto

ECT

sensor

switch

CKP sensor

Ignition coil

ECM

Engine

stop

switch

Regulator

/rectifier

Condenser

Crankshaft rotation
signal sensor

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 283 / 411

Результаты поиска

Содержание RM-Z250

Отзывы: