Suzuki RM-Z250 Скачать руководство пользователя страница 343

Страница: 343 / 411

FRONT FORK AND STEERING 18-21

• Remove the handlebar holders, damper bushings and spac-

ers.

• Remove the steering stem nut

with the special tools.

NOTE:
Hold the steering stem lower bracket to prevent it from falling.



09940-14911: Steering stem nut socket wrench
09940-14960: Steering stem nut socket wrench

• Remove the steering stem lower bracket

and lower bear-

ing.

• Remove the washer

, upper dust seal

and upper bearing

INSPECTION

• Inspect the removed parts for the following abnormalities.

• Distortion of the steering stem
• Bearing wear or damage
• Abnormal bearing noise
• Race wear or damage
• Damper bushing wear or damage

• If any abnormal points are found, replace defective parts with

new ones.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 343 / 411

Результаты поиска

Содержание RM-Z250

Отзывы: