Suzuki RM-Z250 Скачать руководство пользователя страница 356 | Manualshive

Страница: 356 / 411

Suzuki RM-Z250 Скачать руководство пользователя страница 356

REAR SUSPENSION 19-7

OIL REPLACEMENT

TOOLS AND EQUIPMENT

• Following tools and equipment are required to perform oil

replacement.

1

Screwdriver or small punch

7

Rags

2

Vise*

8

Nitrogen tank

3

Drain Pan

9

Filler Hose and Nozzle

4

Oil can

0

Regulator Assembly

5

Beaker

A

Owner’s Service Manual

6

Specified Shock Oil (SS25)

* Not shown in the illustration

OIL REPLACEMENT PROCEDURE

• Remove the rear shock absorber unit from the frame (



19-3),

clean and dry it.

• Remove the spring from the rear shock absorber unit.

(



19-4)

NOTE:
Inspect the rear shock absorber unit for oil leakage.
Turn the rebound damping force adjuster screw

1

counterclock-

wise until it stops so that the rear suspension oil can be poured
easily.

• Remove the valve cap. Press the valve with a screwdriver to

bleed out nitrogen gas.



* Releasing high pressure gas from the rear shock

absorber unit can be hazardous.

* Never perform any servicing until the nitrogen gas

pressure has been released from the rear shock
absorber unit. When releasing the gas pressure,
place a rag over the gas valve and use the tip of a
screwdriver etc. to press the valve. Do not use your
finger to depress the gas valve, and direct the valve
away from your face and body.

«
...
354
355
356
357
358
...
»

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов