manualshive.com logo in svg

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 227 / 411

Поделиться
Скачать
Suzuki RM-Z250 Скачать руководство пользователя страница 227

12-44     FI SYSTEM DIAGNOSIS

“21” (P0110-H/L) IAT SENSOR CIRCUIT MALFUNCTION

NOTE:
After repairing the trouble, clear the DTC using SDS tool. (

12-21)

INSPECTION
Step 1 (When indicating 21:)

1) Stop the engine.
2) Remove the seat and fuel tank rubber band. (

5-2, 13-2)

3) Check the IAT sensor coupler 

1

 for loose or poor contacts. 

If OK, then measure the IAT sensor voltage at the wire side
coupler.

4) Disconnect the IAT sensor coupler 

1

.

5) Connect a 12 volts battery by using the battery lead wire to

the service coupler. (

12-19)

DETECTED CONDITION

POSSIBLE CAUSE

21

Output voltage is not within the following 
range.
0.19 V 

 Sensor voltage < 4.93 V

• IAT sensor circuit open or short.
• IAT sensor malfunction.
• ECM malfunction.

P0110

H

Sensor voltage is higher than specified 
value.

• IAT sensor circuit open or ground circuit open.

• IAT sensor circuit shorted to ground.

L

Sensor voltage is lower than specified 
value.

ECM

B/Br

E2

IAT

Dg

IAT sensor

When using the multi circuit tester, do not strongly touch the terminal of the ECM coupler with
a needle-pointed tester probe to prevent the terminal damage or terminal bend.

1

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов