Suzuki RM-Z250 Скачать руководство пользователя страница 249

Страница: 249 / 411

FUEL SYSTEM AND THROTTLE BODY 13-3

• Lift and hold the fuel tank.
• Disconnect the fuel pump coupler

• Place a rag under the fuel hose

and disconnect the fuel

hose

from the fuel pump.



• Remove the fuel tank assembly.

• Remove the fuel pump assembly

by removing its mounting

bolts

diagonally.



FUEL TANK AND FUEL PUMP
INSTALLATION

Install the fuel pump and fuel tank in the reverse order of
removal. Pay attention to the following points:

• Install a new O-ring

and apply grease to it.





99000-25010: SUZUKI SUPER GREASE “A”

or equivalent

* Be sure to disconnect the fuel hose

by hand. Do

not disconnect the fuel hose

with any tool.

* When removing the fuel tank, do not leave the fuel

hose

on the fuel tank side.

Never disassemble the fuel pump assembly

Replace the O-ring

with a new one.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды