Suzuki RM-Z250 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 411

background image

GENERAL INFORMATION 1-5

FUEL, OIL AND ENGINE COOLANT RECOMMENDATION

FUEL (FOR USA AND CANADA)

Use only unleaded gasoline of at least 90 pump octane (R/2 + M/2).

FUEL (FOR OTHER COUNTRIES)

Use only unleaded gasoline of at least 95 octane (Research Method).

ENGINE OIL (FOR USA)

Suzuki recommends the use of SUZUKI PERFORMANCE 4 MOTOR OIL or equivalent engine oil. Use of
SG/SH/SJ/SL in API with JASO MA/MA1/MA2.
Suzuki recommends the use of SAE 10W-40 engine oil. If SAE 10W-40 engine oil is not available, select an
alternative according to the following chart.

ENGINE OIL (FOR OTHER COUNTRIES)

MOTUL 300V 10W-40 (recommendation) or use a premium qual-
ity 4-stroke motor oil to ensure longer service life of your motorcy-
cle. Use of SG/SH/SJ/SL in API with JASO MA/MA1/MA2. The
recommended viscosity is SAE 10W-40. If an SAE 10W-40 motor
oil is not available, select an alternative according to the right
chart.

BRAKE FLUID

Specification and classification: DOT 4



FRONT FORK OIL

Use SUZUKI FORK OIL SS-05 or an equivalent fork oil.

REAR SUSPENSION OIL

Use REAR SUSPENSION OIL SS-25 or an equivalent suspension oil.

* Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the man-

ufacturer, do not use or mix different types of fluid such as silicone-based and petro-
leum-based fluid for refilling the system, otherwise serious damage will result.

* Do not use any brake fluid taken from old or used or unsealed containers.
* Never re-use brake fluid left over from a previous servicing, which has been stored for a long

period.

«
...
10
11
12
13
14
...
»

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

Бренд: Memphis Shades Страницы: 2

Saddle Tramp BC-BTHBSP

Бренд: Metra Electronics Страницы: 8

Body Protector 4.5 Junior

Бренд: Leatt Страницы: 40

Бренд: R&G Страницы: 2

XRM125 CFT125 2020

Бренд: Honda Страницы: 111

Бренд: Surtek Страницы: 12

Бренд: KTM Power Parts Страницы: 12

Бренд: Datatool Страницы: 9

Бренд: Vetter Страницы: 11

Бренд: Johnny Pag Страницы: 26

Бренд: Power Fist Страницы: 20

Бренд: Ultra-tow Страницы: 6

Бренд: Deco Страницы: 40

PEGASO 650 TRAIL

Бренд: APRILIA Страницы: 12

Бренд: Rivco Страницы: 5

Бренд: 130R Страницы: 57

350 BULLET 1989

Бренд: Royal Enfield Страницы: 114

Бренд: Petzl Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды