manualshive.com logo in svg

Suzuki RM-Z250, Руководство по обслуживанию


Поделиться
Скачать
background image

12-16     FI SYSTEM DIAGNOSIS

SELF-DIAGNOSIS FUNCTION

The self-diagnosis function is incorporated in the ECM. It can be notified by using the FI indicator light assy
(option). To check the function of the individual FI system devices, the dealer mode is provided. In this
check, the tool is necessary to read the DTC (Diagnostic Trouble Code) that identify malfunction location.

DEALER MODE

Connect the FI indicator light assy 

1

 to the mode select coupler. Also, connect a 12 volt battery to the ser-

vice coupler using the battery lead wire 

2

. The DTC is displayed by flashing pattern of FI indicator light. This

means that the ECM has not received signals indicating a correct condition from the sensors or device con-
cerned.

36380-28H00: FI indicator light assy (option)
36890-28H00: Battery lead wire (option)

NOTE:
The FI indicator light turns ON for about 2 seconds after connecting the battery.

Before checking the DTC, do not disconnect the ECM lead wire coupler.
If the coupler from the ECM is disconnected, the DTC is erased and the DTC can not be
checked.

MALFUNCTION

FI INDICATOR LIGHT INDICATION

“NO”

FI indicator light turns OFF.

“YES”

FI indicator light turns ON and blinks.
(Code is indicated from small numeral to large one.)

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

R&G CP0479 Fitting Instructions Manual preview
CP0479
Бренд: R&G Страницы: 13
Avenger 160 STREET Manual preview
160 STREET
Бренд: Avenger Страницы: 31
hepco & becker 650989 00 02 Manual preview
650989 00 02
Бренд: hepco & becker Страницы: 6
Ducati SPORTTOURING ST4S Owner'S Manual preview
SPORTTOURING ST4S
Бренд: Ducati Страницы: 313
Thunderbike Old style Manual preview
Old style
Бренд: Thunderbike Страницы: 7
Yamaha WR450FX Owner'S Service Manual preview
WR450FX
Бренд: Yamaha Страницы: 220
Yamaha WR450FN 2022 Owner'S Service Manual preview
WR450FN 2022
Бренд: Yamaha Страницы: 402
Yamaha WR450F 2021 Owner'S Service Manual preview
WR450F 2021
Бренд: Yamaha Страницы: 402
Yamaha WR450F 2022 Owner'S Manual preview
WR450F 2022
Бренд: Yamaha Страницы: 176
hepco & becker 503998 00 01 Manual preview
503998 00 01
Бренд: hepco & becker Страницы: 2
MV Agusta 2005 F4 BRUTALE 910 S Owner'S Manual preview
2005 F4 BRUTALE 910 S
Бренд: MV Agusta Страницы: 195
MV Agusta F3 User Manual preview
F3
Бренд: MV Agusta Страницы: 467
KOOFU CS-1 Instruction Manual preview
CS-1
Бренд: KOOFU Страницы: 24
Vetter Terraplane Driver'S/Owner'S Manual preview
Terraplane
Бренд: Vetter Страницы: 11
RIEJU MARATHON 250 Owner'S Manual preview
MARATHON 250
Бренд: RIEJU Страницы: 147
Ruroc LITE Instruction Manual preview
LITE
Бренд: Ruroc Страницы: 36
Sinister Sound 98-13 Road Glide/Ultra Installation Instructions Manual preview
98-13 Road Glide/Ultra
Бренд: Sinister Sound Страницы: 14
KTM 60312935044 Information preview
60312935044
Бренд: KTM Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды