Suzuki RM-Z250 Скачать руководство пользователя страница 124

Страница: 124 / 411

6-30 CYLINDER HEAD, CYLINDER AND PISTON

CAMSHAFT (AUTOMATIC DECOMP.) AND CAM CHAIN TENSION
ADJUSTER INSTALLATION

Install the camshaft and cam chain tension in the reverse order
of removal. Pay attention to the following points:

CAMSHAFT (AUTOMATIC DECOMP.)

• Place a wrench over the crankshaft and turn it counter clock-

wise to align the TDC mark

with the center of the groove

of the timing inspection hole.



• Just before installing the camshaft into the cylinder head,

apply MOLYBDENUM OIL SOLUTION to the camshaft jour-
nals, camshaft journal holders and cam faces. Also, apply
engine oil to the camshaft bearings.



MOLYBDENUM OIL SOLUTION

* Pull the cam chain upward, or the chain will be

caught between crankcase and cam drive sprocket.

* To adjust the camshaft timing correctly, be sure to

align the TDC mark

with the index mark

and

hold this position when installing the camshafts.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды