Suzuki RM-Z250 Скачать руководство пользователя страница 275

Страница: 275 / 411

ELECTRICAL SYSTEM 15-3

SEMI-CONDUCTOR EQUIPPED PART

• Be careful not to drop the part with a semi-conductor built in

such as a ECM.

• When inspecting this part, follow inspection instruction strictly.

Neglecting proper procedure may cause damage to this part.

CONNECTING THE BATTERY

WHEN USING THE BATTERY LEAD WIRE (Optional part:
36890-28H00)

• When disconnecting terminals from the battery for servicing,

be sure to disconnect the

battery lead wire, first.

• When connecting the battery lead wires, be sure to connect

the

battery lead wire, first.

WIRING PROCEDURE

Properly route the wire harness according to the “WIRING
HARENESS ROUTING” section. (



20-18 to -20)

INCORRECT

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 275 / 411

Результаты поиска

Содержание RM-Z250

Отзывы: