Suzuki RM-Z250 Скачать руководство пользователя страница 311 | Manualshive

Страница: 311 / 411

background image

FRONT AND REAR BRAKES 17-9

CALIPER INSPECTION

• Inspect the caliper cylinders

A

for scuffing, wear and dam-

age.

• Inspect the pistons

B

for scuffing, wear and damage.

• If necessary, replace the defective parts with a new one.

CALIPER CLEANING

• Flush the caliper ports with pressurized air.
• Wash the caliper pistons and cylinders with fresh brake fluid.



Specification and classification: DOT 4

NOTE:
Do not use gasoline or other cleaning solvents to wash the cali-
per parts.

FRONT CALIPER REASSEMBLY AND
INSTALLATION

Reassemble and install the brake caliper in the reverse order of
removal and disassembly. Pay attention to the following points:

• Apply THREAD LOCK SUPER to the front brake caliper axle

bolt (caliper) and tighten the bolt to the specified torque.



99000-32130: THREAD LOCK SUPER “1360”

or equivalent



Front brake caliper axle bolt (caliper):

25 N·m (2.5 kgf-m, 18.0 lbf-ft)

• Apply SUZKI SILICONE GREASE to the new piston seals.
• Apply brake fluid to the new dust seals and pistons.
• Fit the piston seals, dust seals and pistons.



99000-25100: SUZUKI SILICONE GREASE

or equivalent



Specification and classification: DOT 4

«
...
309
310
311
312
313
...
»

Содержание RM-Z250




























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z250

Бренд: Cake Страницы: 13

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 4

Бренд: Suzuki Страницы: 42

Бренд: Caberg Страницы: 16

Бренд: hepco & becker Страницы: 3

Бренд: Starke Страницы: 20

Бренд: Chicago Electric Страницы: 12

Бренд: Power Fist Страницы: 4

Бренд: Klarfit Страницы: 8

Бренд: TGB Страницы: 219

DORSODURO 750 -

Бренд: APRILIA Страницы: 179

Бренд: Careflon Страницы: 16

Бренд: Benelli Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды