Suzuki RM-Z250 Скачать руководство пользователя страница 210

Страница: 210 / 411

FI SYSTEM DIAGNOSIS 12-27

DTC AND DEFECTIVE CONDITION

DTC No.

DETECTED

ITEM

DETECTED FAILURE CONDITION

CHECK FOR

CKP sensor

The signal does not reach ECM for 1
second or more, after receiving the
IAP sensor input signal.

CKP sensor wiring and mechan-
ical parts
CKP sensor, lead wire/coupler
connection

P0335

TP sensor

The sensor should produce following
voltage.

0.39 V

sensor voltage < 4.51 V

In other than the above range, 14
(P0120) is indicated.

TP sensor, lead wire/coupler
connection

P0120

Sensor voltage is higher than specified
value.

TP sensor circuit shorted to
VCC or ground circuit open

Sensor voltage is lower than specified
value.

TP sensor circuit open or
shorted to ground or VCC circuit
open

ECT sensor

The sensor voltage should be the fol-
lowing.

0.2 V

sensor voltage < 4.9 V

In other than the above range, 15
(P0115) is indicated.

ECT sensor, lead wire/coupler
connection

P0115

Sensor voltage is higher than specified
value.

ECT sensor circuit open or
ground circuit open

Sensor voltage is lower than specified
value.

ECT sensor circuit shorted to
ground

IAP sensor

The sensor should produce following
voltage.

0.23 V

sensor voltage < 4.11 V

In other than the above range, 17
(P0105) is indicated.

IAP sensor, lead wire/coupler
connection

P0105

Sensor voltage is higher than specified
value.

IAP sensor circuit shorted to
VCC or ground circuit open

Sensor voltage is lower than specified
value.

IAP sensor circuit open or
shorted to ground or VCC circuit
open

IAT sensor

The sensor voltage should be the fol-
lowing.

0.19 V

sensor voltage < 4.93 V

In other than the above range, 21
(P0110) is indicated.

IAT sensor, lead wire/coupler
connection

P0110

Sensor voltage is higher than specified
value.

IAT sensor circuit open or
ground circuit open

Sensor voltage is lower than specified
value.

IAT sensor circuit shorted to
ground

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Suzuki RM-Z250, Руководство по обслуживанию, Страница: 210 / 411

Результаты поиска

Содержание RM-Z250

Отзывы: