Suzuki RM-Z250 Скачать руководство пользователя страница 338

Страница: 338 / 411

18-16 FRONT FORK AND STEERING

• Clamp the axle holder

with a vise. Protect the axle holder

with a rag when using a vise.



• Compress the outer tube by hands and install the piston

holder (special tool) between the axle holder

bottom and

lock-nut



09910-20115: Piston holder

• Insert the push rod

into the inner rod.

• Replace the O-ring with a new one.
• Apply fork oil to the O-ring.

• Insert the

shaped projection

of center bolt

into the

push rod

• Slowly tighten the center bolt

until resistance is felt and

check the clearance between the lock-nut

and center bolt

to provide 1 mm (0.04 in) and more.

1 mm (0.04 in) and more

• Turn the lock-nut

counterclockwise until it contacts with the

center bolt

• With the lock-nut

held immovable using a wrench, tighten

the lock-nut/center bolt to the specified torque.



Lock-nut/center bolt: 22 N·m (2.2 kgf-m, 16.0 lbf-ft)

• With the outer tube compressed by hands, remove the special

tool.

* Clamping the axle holder

too tight can damage it

which will affect riding stability.

* Be careful not to clamp the axle holder

too tight.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды