Suzuki RM-Z250 Скачать руководство пользователя страница 156

Страница: 156 / 411

9-8 GEARSHIFTING

GEAR POSITION (GP) SWITCH

REMOVAL

• Drain engine oil. (



2-13)

• Remove the seat, radiator covers and fuel tank.

(



5-2, 13-2, -3)

• Disconnect the GP switch lead wire coupler

• Remove the GP switch lead wire from the clamp

• Remove the engine sprocket cover

and front chain guide

plate

• Remove the clamps

• Remove the GP switch

by removing its bolts

• Remove the O-ring

, switch contacts

and springs

INSPECTION

Refer to page 12-52, -53 for details.

INSTALLATION

Install the gear position switch in the reverse order of removal.
Pay attention to the following points:

• Install the springs

and switch contacts

• Fit the new O-ring

to GP switch

and apply grease to it.





99000-25010: SUZUKI SUPER GREASE “A”

or equivalent

Replace the O-ring

with a new one.

Содержание RM-Z250




























































































































































































































































































































































































































Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды

Suzuki RM-Z250, Руководство по обслуживанию

Результаты поиска

Содержание RM-Z250

Отзывы:

Похожие инструкции для RM-Z250

Бренды по названию

Популярные бренды