Rev. 5.00, 12/03, page 711 of 1088
Select on-chip program
to be downloaded and
set download destination
by FTDAR
Set FKEY to H'A5
DPFR=0 ?
Yes
No
Download error processing
Set the FPEFEQ
and parameter
Initialization
JSR FTDAR 32
Yes
End programming
procedure program
FPFR=0 ?
No
Initialization error processing
Disable interrupts
and bus master operation
other than CPU
Clear FKEY to 0
Set parameter to ER0 and
ER1 (FMPAR and FMPDR)
Programming
JSR FTDAR 16
Yes
FPFR=0 ?
No
Yes
Required data
programming is
completed?
No
Set FKEY to H'5A
Clear FKEY to 0
1
1
Download
Initialization
Programming
MAT
switchover
MAT
switchover
Set FMATS to value other than
H'AA to select user MAT
Set SCO to 1 and
execute download
Clear FKEY and programming
error processing
*
Set FMATS to H'AA to
select user boot MAT
User-boot-MAT selection state
User-MAT selection state
User-boot-MAT
selection state
Note:
*
The MAT must be switched by FMATS
to perform the programming error
processing in the user boot MAT.
Start programming
procedure program
Figure 17-73 Procedure for Programming User MAT in User Boot Mode
The difference between the programming procedures in user program mode and user boot mode is
whether the MAT is switched or not as shown in figure 17-73.
In user boot mode, the user boot MAT can be seen in the flash memory space with the user MAT
hidden in the background. The user MAT and user boot MAT are switched only while the user
MAT is being programmed. Because the user boot MAT is hidden while the user MAT is being
programmed, the procedure program must be located in an area other than flash memory. After
programming finishes, switch the MATs again to return to the first state.
MAT switchover is enabled by writing a specific value to FMATS. However note that while the
MATs are being switched, the LSI is in an unstable state, e.g. access to a MAT is not allowed until
MAT switching is completely finished, and if an interrupt occurs, from which MAT the interrupt
vector is read from is undetermined. Perform MAT switching in accordance with the description
in section 17.27, Switching between User MAT and User Boot MAT.
Except for MAT switching, the programming procedure is the same as that in user program mode.
Содержание H8S/2318 series
