![Porsche 718 Spyder Скачать руководство пользователя страница 111](http://html1.mh-extra.com/html/porsche/718-spyder/718-spyder_owners-manual_1580088111.webp)
108
Garage Door Opener (HomeLink
®
)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
e
Do not repeat this procedure if additional signals
are to be stored on the buttons.
1.
Press and hold the two outer buttons
I
and
III
on
the overhead console for around 20 seconds until
light indicator
A
starts to flash rapidly.
2.
Release the buttons.
The assignment of the HomeLink® buttons has
been deleted. The HomeLink® buttons can be
reprogrammed.
Assigning the garage door opener signal on a
button – fixed code system
On the overhead console
1.
Delete the default codes set in the factory before
assigning for the
first
time.
f
Please see chapter „Deleting stored signals
from the buttons“ on page 107.
2.
Press and hold the desired button on the
overhead console until light indicator
A
starts to
flash slowly.
The button is now ready to learn for 5 minutes.
3.
Stand in front of the vehicle with the original
remote control for the system you wish to
program.
Fig. 78: Position the original remote control in front of the
vehicle
In front of the vehicle
4.
Hold the original remote control around 7.9 in.
(20 cm) from the indicated position (Fig. 78) and
press and hold the transmit button until the turn
signals of the vehicle light up three times or light
indicator
A
on the overhead console flashes
rapidly (this can take more than a minute).
The fact that the vehicle turn signals light up
three times and that light indicator
A
flashes
rapidly confirms that the new signal has been
successfully assigned.
You may need several attempts at different
distances between the vehicle and the original
remote control.
On some systems you will need to press the
transmit button of the original remote control
again if the light indicator on the original remote
control goes out.
5.
The vehicle turn signals flash once to indicate
that the learning readiness period is over: repeat
steps 2 to 4.
6.
To assign other signals on the remaining buttons:
repeat steps 2 to 4.
Assigning the garage door opener signal to a
button – rolling code system
Some systems also require a rolling code to be
programmed for the HomeLink® system. Help from a
second person makes programming easier.
Identifying a rolling code
e
Press the already programmed HomeLink®
button again and hold it down.
If light indicator
A
first flashes rapidly and then
lights up continuously after around 2 seconds,
the equipment operates using a rolling code
system.
f
Information on synchronization is also contained
in the manual for the device you wish to program.
Assigning the garage door opener signal to a button
On the overhead console
1.
Delete the default codes set in the factory before
assigning for the
first
time.
f
Please see chapter „Deleting stored signals
from the buttons“ on page 107.
2.
Press and hold the desired button on the
overhead console until light indicator
A
starts to
flash slowly.
The button is now ready to learn for 5 minutes.
3.
Stand in front of the vehicle with the original
remote control for the system you wish to
program.
In front of the vehicle
4.
Hold the original remote control around 7.9 in.
(20 cm) from the indicated position (Fig. 78 on
page 108) and press and hold the transmit
21_718_GT4_Spyder_BAL_21_WKD 982 02 21 21_KW36.20-24.21_en_US.book Seite 108 Freitag, 24. Juli 2020 11:31 11
Содержание 718 Spyder
Страница 307: ...21_718_GT4_Spyder_BAL_21_WKD 982 02 21 21_KW36 20 24 21_en_US book Seite 304 Freitag 24 Juli 2020 11 31 11...
Страница 308: ...21_718_GT4_Spyder_BAL_21_WKD 982 02 21 21_KW36 20 24 21_en_US book Seite 305 Freitag 24 Juli 2020 11 31 11...
Страница 309: ...21_718_GT4_Spyder_BAL_21_WKD 982 02 21 21_KW36 20 24 21_en_US book Seite 306 Freitag 24 Juli 2020 11 31 11...