Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 80

Страница: 80 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

3.23

Rotate water pump drive tab so it matches the angle
of the drive slot in the engine.

CAUTION

The water pump drive tab and slot must be aligned

properly during installation. Severe engine or water

pump damage will occur if the tab and slot are not in

alignment during water pump installation.

Slide water pump into engine crankcase.

Be sure water pump is fully seated and the drive tab
and slot are properly engaged.

10. Install the (3) water pump mounting bolts, noting

location of shorter bolt and torque to specification.

TORQUE

Water Pump Mounting Bolts:

89 in-lbs (10 Nm)

11. Install the (3) coolant hoses that attach to the water

pump. Be sure orientation and routing are correct.

12. Install the exhaust system as outlined in this chapter.

13. Connect the (-) negative battery cable.

14. Fill and bleed cooling system as outlined in this

chapter.

15. Install the hood, storage bin and passenger seat

base (Chapter 5).

WATER PUMP SERVICE

NOTE

The water pump cover gasket can be replaced while

the water pump housing is still installed in the engine.

Remove water pump assembly as outlined in this
chapter.

Remove the (3) bolts retaining water pump cover to
water pump housing. Discard cover gasket.

Place the water pump drive tab vertically into a soft
jaw vice.

ENGINE

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды