Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 347

Страница: 347 / 447

8.28

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

22. Install the idler gear shaft assembly (A) and gear

cluster assembly (B) into the transmission housing,
all at the same time.

23. Install the rear output shaft assembly (C). Rotate

output shaft assembly to align slots with engagement
dog. Ensure bearing is fully seated upon assembly.

24. Assemble shift shaft rail if previously disassembled.

NOTE

Both shift forks need to be orientated the same way, so

that the shift fork pins are both offset to the same side

of the rail.

25. Install the shift shaft rail (D) and shift forks into the

transmission housing as an assembly. Be sure the
shift forks are engaged into the engagement dogs.

NOTE

Shift fork pins should be offset towards the input shaft

as shown above.

TRANSMISSION

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды