Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 415 | Manualshive

Страница: 415 / 447

background image

10.30

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

TEST 1: Resistance Value of Each Stator Leg

1.

Measure the resistance value of each of the three
stator legs: Y1 to Y2, Y1 to Y3, and Y2 to Y3. Each
test should measure:

0.07 - 0.13 Ω

TEST

CONNECT
METER
LEADS TO:

OHMS
READING

Battery Charge
Coil

Y1 to Y2

0.07 - 0.13 Ω

Battery Charge
Coil

Y1 to Y3

0.07 - 0.13 Ω

Battery Charge
Coil

Y2 to Y3

0.07 - 0.13 Ω

NOTE

If there are any significant variations in ohm readings

between the three legs it is an indication that one of the

stator legs may be weak or failed.

TEST 2: Resistance Value of Each Stator Leg to
Ground

2.

Measure the resistance value of each of the stator
legs to ground: Y1 to Ground, Y2 to Ground, Y3 to
Ground.

3.

Each test should measure:

Open Line (OL)

TEST

CONNECT
METER
LEADS TO:

OHMS
READING

Battery Charge
Coil

Y1, Y2, or Y3
to Ground

Open Line
(Infinity)

NOTE

Any measurement other than Infinity (open) will indicate

a failed or shorted stator leg.

TEST 3: Measure AC Voltage Output of Each
Stator Leg at Charging RPM

4.

Set the selector dial to measure AC Voltage.

5.

Start the engine and let it idle.

6.

While holding the engine at a specified RPM,
separately measure the voltage across each ‘leg’ of
the stator by connecting the meter leads to the wires
leading from the alternator (Y1 to Y2, Y1 to Y3, Y2 to
Y3).

7.

Refer to the following table for approximate AC
Voltage readings according to RPM. Test each leg at
the specified RPM in the table.

8.

Example: The alternator current output reading
should be approximately

21 VAC at 1300 RPM

between each ‘leg’

.

NOTE

If one or more of the stator leg output AC voltage varies

significantly from the specified value, the stator may

need to be replaced.

RPM READING

AC VOLTAGE (VAC)
READING

1300

21 VAC ± 25%

3000

47 VAC ± 25%

5000

79 VAC ± 25%

STATOR (ALTERNATOR) REPLACEMENT

Refer to Engine Chapter “Stator Cover Removal /
Inspection” procedure to service the stator.

NOTE

The stator cover can be removed with the engine

installed in the chassis.

Be sure to thoroughly clean the area around the stator

cover prior to removal.

«
...
413
414
415
416
417
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Raider Extreme 1100D

Бренд: Dazon Страницы: 85

1970 SKI-DADDLER

Бренд: AMF Страницы: 74

Бренд: Can-Am Страницы: 401

Бренд: Atlanta Страницы: 16

Бренд: Canyon Страницы: 83

Бренд: Can-Am Страницы: 140

Бренд: P.Lindberg Страницы: 107

Бренд: U.S. General Страницы: 23

Sportsman 850 2022

Бренд: Polaris Страницы: 188

Sportsman 850 2021

Бренд: Polaris Страницы: 180

Бренд: Ski-Doo Страницы: 38

Бренд: E-Z-GO Страницы: 180

TRANSFORMER 15K-B

Бренд: PARKIT360 Страницы: 26

Grizzly YFM35FGIX

Бренд: Yamaha Страницы: 164

WARRIOR YFM350XNC

Бренд: Yamaha Страницы: 167

Бренд: ParCar Страницы: 114

Бренд: Roketa Страницы: 14

SPORTRAX 250X 2009

Бренд: Honda Страницы: 234

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды