Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 302

Страница: 302 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

7.15

Remove both front drive shafts from the front
gearcase (see "FRONT DRIVE SHAFT - Removal”).

Use the Roll Pin Removal Tool 2872608 to drive the
roll pin out of the front propshaft yoke at the front
gearcase.

Roll Pin Removal Tool (PN 2872608)

Slide the propshaft off the front gearcase input shaft
splines.

Disconnect the AWD wire harness and remove the
plastic zip tie holding the AWD coil pigtail.

Using a 15mm socket, remove the (4) bolts retaining
the front gearcase to the skid plate frame.

Remove the vent hose from the front gearcase.

Remove the grease zerk fitting from the left front
lower control arm.

Remove the front gearcase from the left-hand side
between the upper and lower control arms.

FRONT GEARCASE DISASSEMBLY /
INSPECTION

Drain and properly dispose of gearcase fluid.
Remove any metal particles from the drain plug
magnet.

Remove the (7) cover screws and remove the cover
plate assembly.

FINAL DRIVE

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды