Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 271 | Manualshive

Страница: 271 / 447

background image

6.22

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

3.

Remove nut from puller rod and set aside.

4.

Install puller adapter (Item 10 from kit

PN 2871226

).

5.

Install main adapter (Item D) onto puller.

6.

With towers pointing toward the vise, slide sheave
onto puller rod.

7.

Install removal tool (Item A, B) into center of sheave
with “A side" toward sheave.

NOTE

Use Bushing Tool PA-47336.

8.

Install nut (C) onto end of puller rod and hand
tighten. Turn puller barrel to increase tension on
sheave if needed. Using a hand held propane torch,
apply heat around outside of bushing until tiny
smoke tailings appear.

9.

Turn sheave counterclockwise on puller rod until it
comes free. Lift sheave off puller.

10. Remove nut from puller rod and set aside.

11. Pull bushing removal tool and adapter from puller

rod. Remove bushing from tool and discard.

Drive Clutch Bushing Installation

12. Place main adapter (Item 8) on puller.

13. Apply Loctite® 648 evenly to bushing bore inside

moveable sheave.

14. Set bushing in place on sheave.

15. Insert installation puller tool (Item A/B) with “A” side

down, into center of bushing.

NOTE:

800 EFI Clutch

- Use

Bushing Tool PA-47336

.

16. With towers pointing upward, slide sheave, bushing

and tool onto puller rod.

17. Install nut on puller rod and hand tighten. Turn barrel

to apply additional tension if needed.

18. Turn sheave counterclockwise, making sure bushing

is drawn straight into bore. Continue until bushing is
seated.

19. Remove nut from puller rod and set aside.

20. Remove sheave from puller.

21. Remove installation tool.

Cover Bushing Removal

22. Install main adapter (Item 8) on puller.

«
...
269
270
271
272
273
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

PowerSport W420AC-F01

Бренд: Aria Child Страницы: 52

1970 SKI-DADDLER

Бренд: AMF Страницы: 74

Бренд: Arrowquip Страницы: 16

Beast 1000 Series

Бренд: BMS Страницы: 114

Бренд: NorthStar Страницы: 24

Бренд: Polaris Страницы: 476

Бренд: E-Z-GO Страницы: 204

VIPER 50 ST - SERVICE

Бренд: E-TON Страницы: 68

Бренд: Jayco Страницы: 102

Бренд: Yamaha Страницы: 114

Workman 133-3016

Бренд: Toro Страницы: 8

Бренд: Taylor-Dunn Страницы: 188

Бренд: Taylor-Dunn Страницы: 206

Бренд: Taylor-Dunn Страницы: 260

Бренд: Samsung Страницы: 54

Бренд: Samsung Страницы: 172

Бренд: jcb Страницы: 2

Бренд: Yamaha Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды