Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 389 | Manualshive

Страница: 389 / 447

background image

10.4

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

SWITCHES / CONTROLS

BRAKE LIGHT SWITCH

The brake light switch (A) is located on the front brake
line banjo bolt of the master cylinder. The brake switch
can be accessed through the front left wheel well
opening.

1.

Disconnect the vehicle harness (B) from the brake
switch (A).

2.

Connect an ohmmeter across switch contacts.
Reading should be infinite (OL).

3.

Apply foot brake and check for continuity between
switch contacts. If there is no continuity or if
resistance is greater than 0.5 ohms, clean the switch
contacts and re-test. Replace switch if necessary.

4.

Refer to Chapter 9 if replacing the brake switch, as
the brake bleeding procedure will need to be
performed.

HEADLAMP SWITCH

1.

Disconnect

the

headlamp

switch

harness

by

depressing the connector locks and pulling on the
connector. Do not pull on the wiring.

2.

Test between the 3 sets of outputs (HIGH / LOW /
OFF). If any of the tests fail, replace headlamp
switch assembly.

• Move the switch to HIGH. There should be continuity

between switch pins 2 and 3; 5 and 6.

• Move the switch to LOW. There should be continuity

between switch pins 2 and 3; 4 and 5.

• Move the switch to OFF. There should be continuity

between switch pins 1 and 2; 4 and 5.

NOTE

Pins 7 and 8 provide power and ground to light the

switch lamp.

«
...
387
388
389
390
391
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Taylor-Dunn Страницы: 126

2005 Ranger 4x4

Бренд: Polaris Страницы: 121

can-am MAVERICK SPORT MAX 2003 Series

Бренд: BRP Страницы: 212

Бренд: Cub Cadet Страницы: 28

Бренд: Yutrax Страницы: 8

Бренд: Yamaha Страницы: 859

RECOIL iS CREW 2015

Бренд: Bad Boy Страницы: 60

Бренд: Mahindra Страницы: 79

Бренд: Unimog Страницы: 292

Бренд: Yamaha Страницы: 422

Бренд: Yamaha Страницы: 354

Бренд: Yamaha Страницы: 194

Indy 340 Deluxe 2000

Бренд: Polaris Страницы: 52

2012 RANGER RZR 570

Бренд: Polaris Страницы: 403

Бренд: Suzuki Страницы: 47

Бренд: Suzuki Страницы: 107

Off-Roader 125-4

Бренд: Texas Страницы: 32

Бренд: Snapper Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды