Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 331

Страница: 331 / 447

8.12

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

14. Install the intake plenum and throttle body assembly.

Place the intake plenum runners into the cylinder
head intake adapters.

NOTE

Be sure the intake plenum runners are fully seated in

the intake adapters before tightening the hose clamps.

15. Tighten the hose clamps to specification.

TORQUE

Intake Plenum Hose Clamps:

35 in-lbs (4 Nm)

16. Install the fastener securing the bottom of the intake

plenum to the rear transmission mount. Torque
fastener to specification.

TORQUE

Lower Intake Plenum Fastener:

22 ft-lbs (30 Nm)

17. Wipe any dirt off the fuel line connector and the fuel

rail. Reconnect the fuel line to the fuel rail.

NOTE

Be sure to tug on the fuel line after installing it to make

sure it is secured.

18. Connect the vehicle harness to the T-MAP sensor

(G), ETC (H), fuel injectors (J), rear differential relay
and rear differential solenoid (K).

19. Position the vehicle harness over the intake plenum

and install (5) new plastic tie straps to retain the
harness to the intake plenum.

20. Install the transmission shift cable and washer (L)

onto the bellcrank. Install the retaining clip (M).

TRANSMISSION

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды