Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 420 | Manualshive

Страница: 420 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.35

BATTERY CHARGING PROCEDURE

If battery voltage is 12.6 Vdc or less, the battery may
need recharging. When using an automatic charger, refer
to the charger manufacturer’s instructions for recharging.

Recommended Charging Rate: 1 hour @ 6-10 Amps.
Do not exceed 10 amps when charging the battery.

NOTE

Charge the battery using an automatic charger that will

not exceed 14.6 Vdc. An automatic charger will signal

when charging is complete.

Allow the battery to stand disconnected for at least 1-2

hours after being properly charged. If the voltage drops

below 12.6 volts, charging was ineffective or the battery

needs to be replaced.

WARNING

An overheated battery could explode, causing severe

injury or death. Always watch charging times carefully.
Stop charging if the battery becomes very warm to the

touch. Allow it to cool before resuming charging.

Battery PN 4014043 / 4014132-P

STATE OF
CHARGE

VOLTAGE
(DC)

ACTION

CHARG-
E TIME

100%

12.8 or
more

None, check
again in 3
months

None
Required

75% -
100%

12.6 - 12.8

May need
slight charge

3 - 6 hrs

50% - 75%

12.3 - 12.6

Needs
Charge

5 - 11 hrs

25% - 50%

12.0 - 12.3

Needs
Charge

At least
13 hrs

0% - 25%

12.0 or less

Needs
Charge

At least
20 hrs

NOTE

Follow the charger instructions supplied by the

manufacture regarding the order or connections, switch

positions and when to connect the charger to an outlet.

«
...
418
419
420
421
422
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Oldenbourg group Страницы: 60

Amazon P80 2019

Бренд: Morgan Olson Страницы: 81

Бренд: QERIDOO Страницы: 36

Бренд: Can-Am Страницы: 136

GRIZZLY YFM70GPXJ 2017

Бренд: Yamaha Страницы: 176

Бренд: URBANGLIDE Страницы: 98

Бренд: Tru-Turf Страницы: 48

Бренд: Reeves Страницы: 8

450 MAXXER IRS 4X4 EFI

Бренд: KYMCO Страницы: 1

400 MXU IRS 4X4

Бренд: KYMCO Страницы: 1

Бренд: KYMCO Страницы: 41

Бренд: KYMCO Страницы: 92

Бренд: KYMCO Страницы: 122

Бренд: KYMCO Страницы: 142

Бренд: KYMCO Страницы: 147

Бренд: KYMCO Страницы: 172

Бренд: KYMCO Страницы: 162

Бренд: KYMCO Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды