Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

4.5

EFI SERVICE NOTES

• For more convenient and accurate testing of EFI

components, it is recommended dealers utilize the
Digital Wrench® Diagnostic Software (dealer only).
Some testing may be done manually using the
procedures provided in this chapter.

•

80% of all EFI problems are caused by wiring
harness connections.

• For the purpose of troubleshooting difficult running

issues, a known-good ECU from another

RANGER

XP

900 of the same model and year may be used without
damaging system or engine components.

• Never attempt to service any fuel system component

while engine is running or ignition switch is "on."

• Cleanliness is essential and must be maintained at all

times when servicing or working on the EFI system.
Dirt, even in small quantities, can cause significant
problems.

• Do not use compressed air if the system is open.

Cover any parts removed and wrap any open joints
with plastic if they will remain open for any length of
time. New parts should be removed from their
protective packaging just prior to installation.

• Clean any connector before opening to prevent dirt

from entering the system.

• Although every precaution has been taken to prevent

water intrusion failure, avoid direct water or spray
contact with system components.

• Do not disconnect or reconnect the wiring harness

connector to the control unit or any individual
components with the ignition "on." This can send a
damaging voltage spike through the ECU.

• Do not allow the battery cables to touch opposing

terminals. When connecting battery cables attach the
positive (red) cable to positive (+) battery terminal first,
followed by negative (black) cable to negative (-)
battery terminal.

• Never start the engine when the cables are loose or

poorly connected to the battery terminals.

• Never disconnect battery while engine is running.
• Never use a battery boost-pack to start the engine.
• Do not charge battery with key switch "on."
• Always disconnect negative (-) battery cable lead

before charging battery.

• Always unplug ECU from the wire harness before

performing any welding on the unit.

FUEL SYSTEM - GENERAL

«
...
152
153
154
155
156
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Ezgo Страницы: 102

Бренд: WABASH COMMUNICATIONS Страницы: 47

Twister UM250IIR

Бренд: Hammerhead Страницы: 67

Бренд: LAMAX Страницы: 150

YUM1A UMAX RALLY 2021

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 158

GRIZZLY YFM70GPAP 2023

Бренд: Yamaha Страницы: 180

KODIAK ULTRAMATIC YFM400FWAN 2000

Бренд: Yamaha Страницы: 184

Бренд: Can-Am Страницы: 144

Бренд: Mahindra Страницы: 79

Бренд: Yerf-Dog Страницы: 25

Бренд: Palms Страницы: 19

Бренд: Landoll Страницы: 88

Бренд: Westbrook Trailers Страницы: 24

Бренд: Wood-mizer Страницы: 90

Multilander Logging Trailer with Utility Box

Бренд: Woodland Mills Страницы: 36

Бренд: Woodland Mills Страницы: 48

Бренд: TIMBCO Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды