Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

5.39

BALL JOINT SERVICE

SERVICE PREPARATION

NOTE

Do not reuse a ball joint if it has been removed. If

removed, it must be replaced. Use this removal

procedure only when replacing the ball joint.

Ball joint tool PU-50506 will allow the upper and lower

ball joints to be replaced with the A-arm installed on the

vehicle.

The A-arm does not need to be removed to perform this
procedure if ball joint tool PU-50506 is used.

1.

Properly lift and support the vehicle by the frame.

2.

Remove the appropriate front wheel.

3.

To service the upper ball joint:

4.

Remove and discard the two front brake caliper
mounting bolts and remove the caliper from the
brake disc (see “Brakes” chapter).

5.

Remove and discard the upper ball joint pinch bolt.

6.

If necessary, remove the lower front shock fastener
from the A-arm to gain enough clearance to install
ball joint tool (PU-50506) on the upper ball joint.

7.

To service the lower ball joint:

8.

Remove and discard the lower ball joint pinch bolt.

9.

If necessary, remove the lower front shock fastener
from the A-arm to gain enough clearance to install
ball joint tool (PU-50506) on the lower ball joint.

BALL JOINT REMOVAL

1.

Remove the retaining ring from the ball joint.

2.

Install Spacer (A) over the top of the ball joint face.

3.

Place Removal Adaptor (B) over the ball joint shaft.

4.

Install the Press Asm. (C) onto the A-arm to engage
the ball joint Removal Adapter.

NOTE

Be sure the Press Asm. opening is only contacting the

Spacer (A) and not the ball joint face.

BODY / STEERING / SUSPENSION

«
...
236
237
238
239
240
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Monowalker Страницы: 27

Бренд: Recon Страницы: 102

Бренд: Ezytrail Страницы: 28

Бренд: Polaris Страницы: 109

Бренд: Valor Страницы: 41

Бренд: Polaris Страницы: 68

Renegade 570 2016

Бренд: Can-Am Страницы: 534

Бренд: Primo Water Страницы: 12

1990 DS Gasoline Golf Car

Бренд: Club Car Страницы: 20

Бренд: Club Car Страницы: 44

Бренд: Jula Страницы: 65

Workman HD 07369

Бренд: Toro Страницы: 56

Бренд: Toro Страницы: 64

Бренд: Dometic Страницы: 116

Бренд: KYMCO Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды